|
Processor family :
Dual-Core Processor
Intel® Pentium® G2130 (3.20GHz/2-core/3MB/55W, 1600) Processor |
|
Cache Memory :
Integrated 1x3MB Level3 Intel® Smart Cache |
|
Chipset :
Intel® C204 Series Chipset
NOTE: For more information regarding Intel® chipsets, please see the following URL:
http://www.intel.com/products/server/chipsets/. |
|
Upgradeability :
Up to 4 DIMM slots available for higher memory capacity
Up to 4 LFF Hard Drives
۴ PCIe 2.0 I/O slots for additional communications and storage expansion
Optical Drive Bay |
|
On System Management Chipset :
HP iLO (Firmware: HP iLO3)
NOTE: For more information, visit: http://www.hp.com/go/ilo |
|
Memory Protection :
ECC |
|
Memory :
Type
PC3-12800E-11 unbuffered DDR3 ECC up to 1600MT/s
DIMM Slots
Total 4 DIMM slots
Standard
۲GB GB (1x2GB)
Maximum
۳۲GB |
|
Network Controller :
HP NC112i 1-Port Ethernet Server Adapter (X1) |
|
HP Server ROM :
HP ROM (Read Only Memory) is now digitally signed using HP’s Corporate Signing Service. This signature is verified before the flash process starts, reducing accidental programming and preventing malicious efforts to corrupt system ROM.
HP ROM provides for essential initialization and validation of hardware components before control is passed to the customer-installed operating system. The ROM also provides the capability of booting from various fixed media (HDD, CD-ROM) and removable media (USB), to continue operation to the operating system.
HP ROM performs very early configuration of the video controller, to allow monitoring of initialization progress via an attached monitor. If configuration or hardware errors are discovered during this early phase of hardware initialization, suitable messages are now displayed on the connected monitor. Additionally, these configuration or hardware errors are logged to the Integrated Management Log (IML) to assist in diagnosis.
HP’s ProLiant ROM is used to configure the following:
Processor and chipset status registers
System memory, memory map, and memory initialization
System hardware configuration (Integrated PCI devices and optional PCIe cards).
Customer-specific BIOS configuration (using the HP ROM-Based Setup Utility (RBSU).
NOTE: For further information, please refer to HP’s RBSU (ROM based setup utility) user guide: www.hp.com/support/rbsu. |
|
Storage Controller :
HP Embedded Smart Array B110i SATA RAID Controller (RAID 0/1/10)
NOTE: Supports up to two (2) 3.0Gb/s SATA hard disk drives only
NOTE: For set up instructions, please refer to the HP ProLiant ML100 series server user guide at: http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01708878/c01708878.pdf
NOTE: For general information about HP Smart Array B110i SATA RAID Controller, please go to: http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers/smartarrayb110i/
index.html |
|
Internal Storage Devices :
Optical Drive
HP Half-Height SATA DVD (Optional)
Standard Hard Drive
(۱) Non hot-plug LFF SATA
Hard Drive Bay Configurations (depending on option)
۲ HDDs (no optical)
Convert optical bay to 2nd LFF HDD bay
NOTE: Requires purchase of HP ML10 Hard Drive Enablement Kit (#730641-B21)
۳ HDDs (with optical)
Replace internal single HDD carrier with a 3 x LFF carrier (leaving optical bay available)
NOTE: Requires purchase of HP ML10 4 LFF Hard Drive Enablement Kit (#742971-B21)
NOTE: The ML10 4LFF Hard Drive Enablement Kit: includes one carrier to convert the Optical Drive bay to one LFF Drive and includes a second carrier to support 3 internal LFF HDDs. The 3 x LFF carrier replaces the standard 1 x LFF carrier. For 3HDD Configurations, the carrier to convert the Optical Drive day to one LFF Drive is left unused.
۴ HDDs (no optical)
Replace internal single HDD carrier with a 3 x LFF carrier and convert optical bay to support 1 x LFF HDD
NOTE: Requires purchase of HP ML10 4 LFF Hard Drive Enablement Kit (#742971-B21)
NOTE: The ML10 4LFF Hard Drive Enablement Kit: includes one carrier to convert the Optical Drive bay to one LFF Drive and includes a second carrier to support 3 internal LFF HDDs. The 3 x LFF carrier replaces the standard 1 x LFF carrier. Both carriers need to be installed. |
|
Maximum Internal Storage :
Non-Hot Plug LFF SATA
۸TB
۴ x 2TB
NOTE: Requires purchase of optional HP ML10 4 LFF Hard Drive Enablement Kit (#742971-B21) |
|
Interfaces :
Video Port
۱
USB 2.0 Ports
۷ total (4 rear, 2 front panel, 1 internal)
Network RJ-45 (Ethernet)
۱ (shared for HP Integrated Lights-Out)
Remote Management
iLO3 remote management support |
|
Industry Standard Compliance :
ACPI V3.0b Compliant
PCI Express Rev 2.0
PXE Support
WOL Support
IPMI 2.0 compliance
DCMI 1.0
Microsoft® Logo certifications
Red Hat Enterprise Linux Logo certifications
SUSE Linux Enterprise Server Logo certifications
USB 2.0 |
|
Common Slot Power Supply :
۳۰۰ Watts 80+ Bronze Non-Hot Plug, Non redundant Power Supply |
|
System Fans :
One Non-redundant system fan ships standard
One Non-redundant CPU heatsink fan ships standard |
|
Operating Systems and Virtualization Software Support for ProLiant Servers :
Microsoft Windows Server
SUSE Linux Enterprise Server (SLES)
NOTE: For more information on HP’s Certified and Supported ProLiant Servers for OS and Virtualization Software and latest listing of software drivers available for your server, please visit our Support Matrix at: http://www.hp.com/go/ossupport and our driver download page: HP ProLiant ML10 |
|
Graphics :
Integrated Matrox G200 video standard
۱۲۸۰ x 1024 (32 bpp)
۱۹۲۰ x 1200 (16 bpp)
HP iLO 4 On System Management Memory
۱۶ MB Flash
۲۵۶ MB DDR 3 with ECC (112 MB after ECC and video) |
|
Form Factor :
Micro ATX Tower (4U). |
|
On System Management :
HP iLO Management Engine
HP iLO Management Engine is a comprehensive set of embedded management features supporting the complete lifecycle of the server, from initial deployment, through ongoing management, to service alerting and remote support. HP iLO Management Engine comes standard on all HP ProLiant Gen8 servers. The HP iLO Management Engine portfolio includes:
HP iLO: The HP iLO (Integrated Lights-Out) management processor is the core foundation for the HP iLO Management Engine
HP Agentless Management: Provides built in server health monitoring and alerting capability without OS agents, that starts working the moment a power cord and an Ethernet cable are connected.
HP Active Health System: Always on, continuous monitoring for increased stability and shorter downtimes; 100% configuration history; Health and service alerts and easy export and upload to Service and Support.
HP Intelligent Provisioning: Lets customers provision and configure a single server without any separate media. No more SmartStart CDs or Smart Update Firmware DVD are needed.
To start Intelligent Provisioning:
Press the F10 key during the ProLiant Gen8 server boot process (also known as power on self test or POST).
Please go to the Intelligent Provisioning website at www.hp.com/go/intelligentprovisioning for additional information and to view usage videos.
Use the Service Pack for ProLiant (SPP) at www.hp.com/go/spp to get firmware and software updates.
HP iLO Mobile App: Enables the ability to access, deploy, and manage your server anytime from anywhere from select smartphones and mobile devices. For additional information please visit: www.hp.com/go/ilo/mobileapp
NOTE: For more information, visit: http://www.hp.com/go/ilo or HP iLO Management Engine technologies whitepaper |
|
HP Insight management :
HP Integrated Lights-Out 3 (3)
HP Integrated Lights-Out 3 (iLO) simplifies server setup, health monitoring, and lights-out remote administration of ProLiant ML, DL, and BL servers. HP iLO functions without additional software and can be accessed from any location via a web browser. HP iLO works hand-in-hand with HP Systems Insight Manager, Insight Control suites, and Insight Dynamics for ProLiant, helping customers unleash the value of the ProLiant platform and deliver the highest possible quality of IT service. For more information, visit: www.hp.com/go/iLO |
|
Security :
Power-on password
Setup password
Secure Sockets Layer (SSL)
Secure Shell (SSH)
iLO 3 (Integrated Lights-Out 3) has 12 customizable user accounts and SSL encryption
iLO 3 can be disabled via a Global Setting
iLO Advanced supports directory services integration |
